Add ThreatListPro's curated VPN brute force blocklist to your pfSense firewall using pfBlockerNG. Automatically block attackers before they reach your VPN portal.
Start 14-Day Free Trial (No Card)What blocklist URL do I use on pfSense? A plain-text list of IPv4 addresses and CIDR ranges served over HTTPS can be loaded in pfBlockerNG or a built-in URL Table (IPs) alias. Add it as an IPv4 list with the action Deny Inbound on the WAN, or as an alias used in your own WAN block rule above the rule that allows your VPN port. To reduce VPN brute-force attempts overall, patch the firewall, require MFA or certificate authentication, limit portal exposure where practical, and put an external IP list in a logged deny rule ahead of the VPN service. Test the free sample first in an allow rule with logging on, placed above your VPN allow rule, and review the hits; allow-list trusted networks before you change the action to deny.
Free test list (200 entries, no signup): https://raw.githubusercontent.com/pcchiu2023/threatlistpro-blocklist/main/data/sample/blocklist.txt · GitHub repository with setup examples
pfSense is popular with SMBs and homelabs alike. If your OpenVPN or WireGuard port is exposed to the internet, bots are already probing it.
Automated scanners continuously sweep the internet for open VPN ports. Once found, they launch credential-stuffing attacks using leaked password databases. pfSense logs fill with failed authentication attempts, consuming CPU cycles and disk space. Without proactive blocking, it is only a matter of time before a weak or reused credential is guessed.
pfBlockerNG is pfSense's most popular package for IP and DNS blocking. ThreatListPro feeds directly into pfBlockerNG as a custom IP list, blocking known VPN attackers at the firewall level. No failed logins, no log noise, no wasted resources. The list is checked for new attackers every 6 hours and pfBlockerNG pulls it on your configured schedule.
Add ThreatListPro as a custom IPv4 blocklist in pfBlockerNG. Works with pfSense CE and pfSense Plus.
In pfSense, go to System > Package Manager > Available Packages. Search for pfBlockerNG and click Install. Either pfBlockerNG or pfBlockerNG-devel works for this list.
Sign up at threatlistpro.com and copy your unique feed URL from your welcome email:https://api.threatlistpro.com/v1/YOUR_API_KEY/blocklist.txt
Navigate to Firewall > pfBlockerNG > IP > IPv4. Click Add to create a new IPv4 group. Set the alias name to ThreatListPro, paste the feed URL as the source, set format to Auto, and action to Deny Inbound. Set the update frequency to Every hour.
Go to pfBlockerNG > General and ensure the package is enabled. Then navigate to pfBlockerNG > Update and click Run with Force Update selected to load the blocklist immediately.
Check Firewall > pfBlockerNG > Reports > Alerts to see blocked IPs as they happen. You can also verify the alias is populated under Diagnostics > Tables by looking for the pfB_ThreatListPro_v4 table.
Choose the pfSense alias type based on whether the external IP list must update after the initial import.
| Alias type | Refresh behavior | Update frequency | When to use |
|---|---|---|---|
| URL (IPs) | Imports the URL contents into a Network-type alias stored in the configuration when you save it. | No interval setting. pfSense's source also runs a URL alias updater every 24 hours. | Small lists only: Netgate documents up to 3,000 entries read from each URL. |
| URL Table (IPs) | Keeps the downloaded content in a persistent firewall table and periodically fetches it again. | The configured interval is measured in days; pfSense checks once per day to see whether an update is due. | Large or changing external IP blocklists. |
Check the alias type, ruleset, table capacity, and HTTPS validation before changing the feed.
Use URL Table (IPs), not URL (IPs), for a feed that must change. A URL alias is meant for small lists (Netgate documents up to 3,000 entries per URL) and has no update interval setting. A URL Table alias keeps the downloaded file as a persistent table and checks once per day to see whether its day-based interval has elapsed.
Open Diagnostics > Tables and select the alias. If it is absent, make sure a rule references it, because an alias becomes a firewall table only after the ruleset loads it. For inbound VPN protection, use the alias as the source in a WAN block rule placed above the VPN pass rule, then apply changes.
To download a URL Table alias again now, open Diagnostics > Tables, select the alias and click Update. Netgate's documentation mentions that button only for bogon tables, but pfSense's own page code runs /etc/rc.update_urltables now forceupdate for a selected URL Table alias. Status > Filter Reload reloads the ruleset and stored table; Netgate does not document it as a new download.
Check System > Advanced > Firewall & NAT. Firewall Maximum Table Entries defaults to 400,000, and Netgate recommends capacity for at least twice the total entries across all aliases. If the limit is too low, the ruleset may fail to load. Increase it only with enough RAM; Netgate suggests roughly 1 KB per entry conservatively.
Keep Verify HTTPS certificates when downloading alias URLs enabled. The feed server must present a certificate with a valid trust chain. If a private server uses a private CA, add that CA under System > Certificates and place it in the firewall trust store instead of disabling verification.
Open Status > Filter Reload and run Reload Filter. The page reports progress; a final Done. indicates completion, while an error identifies where loading stopped. Then return to Diagnostics > Tables and inspect the alias. This verifies the stored table and ruleset; use Update on Diagnostics > Tables (step 3) to force a new download.
See how a VPN-focused blocklist compares to other approaches for protecting your pfSense firewall.
| Feature | ThreatListPro | Manual Blocking | Enterprise Threat Feeds |
|---|---|---|---|
| VPN brute-force focused | ✓ | ✗ | ✗ |
| Checked for new attackers every 6 hours | ✓ | ✗ | ✓ |
| pfBlockerNG compatible | ✓ | ✗ | ✓ |
| Setup in under 5 minutes | ✓ | ✗ | ✗ |
| Price | $19.99/mo | Staff time | $500+/mo |
In the pfSense web interface, go to System > Package Manager > Available Packages and search for pfBlockerNG. Click Install. After installation, navigate to Firewall > pfBlockerNG to begin configuration. Either pfBlockerNG or the pfBlockerNG-devel package works for this IPv4 list.
In pfBlockerNG, go to the IPv4 tab and click Add. Create a new alias group, paste your ThreatListPro feed URL as the source, set the format to Auto, action to Deny Inbound, and update frequency to Every hour. Then run a Force Update to load the list immediately.
Yes. ThreatListPro provides a standard plaintext IP list that works with pfBlockerNG on both pfSense Community Edition and pfSense Plus. Menu labels can differ between package versions, so match the field names shown on your firewall.
URL (IPs) has no update interval setting and is meant for small lists: Netgate documents that pfSense reads up to 3,000 entries from each URL. Use URL Table (IPs) for a changing external blocklist. Its interval is measured in days, and pfSense checks once daily to determine whether the configured interval has elapsed.
Yes. Select the URL Table alias in Diagnostics > Tables and click Update. In pfSense's own source, that button runs /etc/rc.update_urltables now forceupdate for the selected alias, so it downloads again without waiting for the interval. Netgate's documentation mentions the button only for bogon tables.
Pair pfBlockerNG with ThreatListPro for automated VPN brute force protection.
Start 14-Day Free Trial (No Card)ThreatListPro provides a standard IP blocklist feed compatible with any firewall that supports external lists.
Last updated November 18, 2026. Technical details were checked against Netgate's pfSense documentation.
Alias Types - URL and URL Table behavior, entry limits, and day-based update intervals.
Firewall Table Contents - viewing aliases under Diagnostics > Tables (the docs describe its Update button only for bogon tables).
pfSense source: diag_tables.php - the Update button also force-downloads a selected URL Table alias.
pfSense source: pfSense-rc - the 24-hour URL alias updater.
Firewall & NAT - maximum table entries and HTTPS certificate verification.
Filter Reload Status - manually reloading the firewall ruleset.
Alias Usage - referencing aliases in firewall rules.
Rule Methodology - WAN rule direction and first-match ordering.
Certificate Authority Management - trusting a private CA for URL Table connections.
Learn more about IP blocklists, VPN security, and how ThreatListPro compares to alternatives.